Siemens SIMATIC IPC1047 Скачать руководство пользователя | Manualshive

Страница: 30 / 136

background image

Installing and connecting the device

3.2 Mounting the device

SIMATIC IPC1047

30

Operating Instructions, 09/2018, A5E45118479-AA

3.1.3

Permitted mounting positions

Optional installation locations

The device can be mounted horizontally in control desks, switching cabinets and 19" rack

systems.

NOTICE
Operation in closed rooms
The device is approved for operation in closed rooms only. Pay attention to the ambient

and environmental conditions.

3.2

Mounting the device

3.2.1

Installation guidelines

WARNING

Danger, high voltage
A high voltage may be present in the switchgear cabinet and could cause a dangerous

electric shock.
It may result in death or serious physical injury.
Isolate the power supply to the switchgear cabinet before opening it. Ensure that the power

to the switchgear cabinet cannot be turned on accidentally.

NOTICE
Fire hazard
If you install the device in an unapproved mounting position or if you do not observe the

ambient conditions, the device can overheat. UL approval and conformity with the low-

voltage directive (EN 60950-1:2006 and DIN EN 60950-1:2006-11) become void.
Overheating can cause a fire. Proper functioning of the device is no longer guaranteed.
Before you install the device, note the following general installation information.

Note
The device meets the requirements for fire protection enclosures in accordance with

EN 60950-1. It can therefore be installed without an additional fire protection enclosure.

«
...
28
29
30
31
32
...
»

Содержание SIMATIC IPC1047









































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC IPC1047

Бренд: Napoleon Страницы: 2

Бренд: Ultraflex Страницы: 3

Cutler-Hammer ATC-300

Бренд: Eaton Страницы: 32

Бренд: Bondura Страницы: 10

Бренд: TE Connectivity Страницы: 15

Z62-H360.02 S19W2/3

Бренд: Jäger Страницы: 40

GAT Rotopack BAT

Бренд: Moog Страницы: 27

Бренд: Eaton Страницы: 8

Бренд: M-system Страницы: 4

Бренд: L&T Electrical & Automation Страницы: 56

Бренд: displayit Страницы: 6

Бренд: Zimmer Страницы: 40

Power Panel 500 Series

Бренд: B&R Страницы: 319

Бренд: Pentair Страницы: 16

Бренд: FLO-DYNAMICS Страницы: 19

Бренд: Magnaflux Страницы: 58

Бренд: Walinga Страницы: 66

UPC-7210 Series

Бренд: IBASE Technology Страницы: 77

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды