Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 22 / 136

Safety Instructions

2.1 General safety instructions

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

NOTICE
Danger for machine and plant through unauthorized remote access
IPMI remote monitoring has a known standard password in the delivery state. This allows

unauthorized access to the device from the outside by third parties. Damage to the

machine or plant is not excluded.

•

Change the IPMI password immediately after commissioning the device. You can find

additional information in the sections "Monitoring with sensors (Page 49)" and

"IPMI Setup (Page 114)".

•

Alternatively, do not connect IPMI-enabled devices to the Internet or any network at all.

Damage caused by transportation and storage

NOTICE
Damage to the device during transport and storage
If a device is transported or stored without packaging, shocks, vibrations, pressure and

moisture may impact the unprotected unit. Damaged packaging indicates that ambient

conditions have already had a massive impact on the device and it may be damaged.
This may cause the device, machine or plant to malfunction.

•

Keep the original packaging.

•

Pack the device in the original packaging for transportation and storage.

WARNING

Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in the machine or

plant. A damaged device has unpredictable properties and states.
Death or serious injury could occur.

•

Avoid installing and commissioning a damaged device.

•

Label the damaged device and keep it locked away. Send off the device for immediate

repair.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды