Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 77 / 136

Device maintenance and repair

7.3 Manage onboard RAID system

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

7.3.2

RAID software

The free RAID software "Intel Rapid Storage Technology" offers additional advanced

functions for the use and management of the RAID system.
1.

Select the RAID software via "Start > Programs > Intel Rapid Storage Technology".

Select "Manage" > "Advanced" to display details of the RAID system.

Select "Help" > "System Report" > "Save" to create a report with the details of the RAID

system.

7.3.3

Checking the status of the RAID system

By default, the status of the RAID system is displayed in the Windows Event Viewer and in a

log file of the program. If an error occurs, a hard disk can be synchronized at the operating

system level.

Note
It may take a very long time (hours or even days in the case of a high drive load) to

synchronize a new hard disk in the background, depending on its size and on the system

load.
The redundant system state is reached again only after synchronization is completed.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды