Siemens SIMATIC IPC1047 Скачать руководство пользователя | Manualshive

Страница: 101 / 136

background image

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

101

Technical specifications

8

8.1

Certificates and approvals

Note on rating plate

Note
Approvals on the rating plate
The following overview provides information on possible approvals.

Only the approvals printed on the rating plate apply to the device.

ISO 9001 certificate

The Siemens quality management system for our entire product creation process

(development, production and sales) meets the requirements of ISO 9001.
This has been certified by DQS (the German society for the certification of quality

management systems).

Software license agreements

If the device is supplied with installed software, observe the enclosed license agreements.

USA and Canada

The following approvals are available for the device:
Product safety

Approval (NRTL / CSA)

Nationally Recognized Testing Laboratory (NRTL)
According to UL 60950-1 and CAN/CSA-C22.2 No. 60950-1-07

EMC

USA (FCC)

Federal

Communications

Commission
Radio Frequency

Interference Statement

This device complies with part 15 of the FCC Rules:
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

«
...
99
100
101
102
103
...
»

Содержание SIMATIC IPC1047









































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC IPC1047

Бренд: Haas Страницы: 12

WAGO-PERSPECTO 762 Series

Бренд: WAGO Страницы: 2

Бренд: +GF+ Страницы: 2

Sportsman EXG 14/12

Бренд: M&R Страницы: 98

Бренд: siat Страницы: 102

Бренд: YASKAWA Страницы: 47

Бренд: DCD Страницы: 4

Бренд: Zimmer Страницы: 19

Бренд: TDI Страницы: 39

Бренд: Beckhoff Страницы: 44

Бренд: Habegger Страницы: 21

Бренд: Zimmer Страницы: 40

Бренд: Panblast Страницы: 9

ECORICH R 40 Series

Бренд: Daikin Страницы: 104

Бренд: ABB Страницы: 128

Бренд: Watts Страницы: 12

Бренд: Westinghouse Страницы: 6

Бренд: Advanjet Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды