Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 79 / 136

Device maintenance and repair

7.3 Manage onboard RAID system

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

7.3.5

Special feature: Replacing hard disk in the RAID system when switched off

The RAID system does not automatically boot up when restarted if a defective hard disk was

replaced while the RAID system is switched off. Therefore, place the RAID system in the first

place of the bootable sources in the BIOS setup menu "Boot". Otherwise, the system will

boot from the hard disk you have just installed and the message "Operating system not

found" will be displayed.

7.3.6

Integrating a new hard disk drive in the RAID system

The RAID system is configured in the delivery state so that a new hard disk must be

integrated manually in case of an error. To integrate the hard disk automatically, activate

"Automatic rebuild" in the "Preferences" menu of the RAID software.

Automatic integration of a hard disk

NOTICE
Data loss
The hard disk to be integrated is not checked for partition information or existing data

during automatic integration.
All partitions and data on the hard disk are deleted without warning. Insert only a brand-new

hard disk.

Requirement:

●

"Automatic rebuild" is selected in the "Preferences" menu of the RAID software.

●

The hard disk to be integrated is brand new or is set up as a spare drive. Notes on

creating spare drives are available in the controller documentation.

Sequence
The following figure is an example for the automatic rebuilding process.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды