Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 78 / 136

Device maintenance and repair

7.3 Manage onboard RAID system

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

NOTICE
Operator errors on the machine or plant
Data is synchronized if a hard disk fails. Depending on the work load of the processor and

hard disks, the system may react with some delay. Execution of keyboard, mouse or touch

screen commands may be briefly delayed in extreme situations. This could result in

operator errors on the machine or plant.
Do not operate safety-critical functions when a hard disk has failed.

7.3.4

Displaying a defective hard disk of a RAID system in the RAID software

Note
Always replace the defective hard disk with a new hard disk of the same type and capacity.

In order to return to the safe RAID state after an error, the faulty hard disk must be replaced

by a new hard disk.
The RAID software indicates the following:

●

A defective hard disk

●

Details of the functioning hard disk:
The functioning hard disk is indicated by BIOS with its port number or by the RAID

software with its device port number.
The following figure shows the corresponding window in the RAID software with a RAID1

system.

You can find information on how to detect and replace a defective hard disk in the RAID

system in the section "Replacing a defective hard disk drive in the RAID system (Page 60)".

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды