Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 7 / 136

Table of contents

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

7.5

Removing and installing hardware ..................................................................................... 83

7.5.1

Replacing device fans ....................................................................................................... 83

7.5.2

Replacing the backup battery ............................................................................................ 85

7.5.3

Replacing the redundant power supply module .................................................................. 87

7.5.4

Replacing the processor .................................................................................................... 88

7.6

Installing the software ........................................................................................................ 90

7.6.1

Back-up authorization or license key .................................................................................. 90

7.6.2

Restoring the factory settings of the operating system and partitions (Restore) .................. 90

7.6.3

Updating the operating system .......................................................................................... 92

7.6.4

Installing drivers and software ........................................................................................... 92

7.6.5

Installing Windows (Recovery) ........................................................................................... 93

7.6.6

Setting up the language selection using the Multilanguage User Interface (MUI) ................ 98

7.6.7

Installing Hardware RAID controller software ..................................................................... 99

7.7

Recycling and disposal .................................................................................................... 100

Technical specifications ............................................................................................................. 101
8.1

Certificates and approvals ............................................................................................... 101

8.2

Directives and declarations .............................................................................................. 102

8.2.1

CE marking ..................................................................................................................... 102

8.2.2

ESD guideline ................................................................................................................. 103

8.3

Dimension drawings ........................................................................................................ 105

8.3.1

Dimensional drawing of the device .................................................................................. 105

8.3.2

Dimension drawing for telescope rails .............................................................................. 106

8.3.3

Dimension drawing of the expansion cards ...................................................................... 106

8.4

Technical specifications ................................................................................................... 107

8.4.1

General specifications ..................................................................................................... 107

8.4.2

Current and power requirements ..................................................................................... 110

8.4.3

Power supply (AC) .......................................................................................................... 111

8.4.4

AC power supply, redundant............................................................................................ 112

8.5

Hardware description....................................................................................................... 113

8.5.1

Motherboard .................................................................................................................... 113

8.6

BIOS description ............................................................................................................. 113

8.7

IPMI Setup ...................................................................................................................... 114

Technical support ...................................................................................................................... 115
A.1

Troubleshooting .............................................................................................................. 115

A.2

RAID system and device startup ...................................................................................... 117

A.3

Notes on the use of third-party modules ........................................................................... 118

Abbreviations ............................................................................................................................ 119

Glossary ................................................................................................................................... 125

Index ....................................................................................................................................... 133

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды