Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 113 / 136

Technical specifications

8.5 Hardware description

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

113

8.5

Hardware description

8.5.1

Motherboard

You can find more detailed information from the manufacturer at "

Supermicro (

https://www.supermicro.com/products/motherboard/xeon/c600/x10dri.cfm

)".

Specifically, the manual for motherboard:

X10DRi (

https://www.supermicro.com/manuals/motherboard/C606_602/MNL-1491.pdf

)

8.6

BIOS description

BIOS Setup program

The BIOS Setup program, or BIOS Setup for short, is located, together with the setup

parameters, in a FLASH block on the motherboard. You change the setup parameters of the

device in the BIOS Setup. Examples: System time, hard disks or boot order.
Press <Del> during booting to open the BIOS Setup.

Changing the device configuration

Your device configuration is preset for operating with the included software. You should only

change the default setup parameters if you have made technical changes to your device, or

if a fault occurs when the device is switched on.

Note
Documentation
You can find the BIOS description from the manufacturer at

Supermicro (

https://www.supermicro.com/products/motherboard/xeon/c600/x10dri.cfm

)

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды