Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 45 / 136

Commissioning the device

4.4 Notes on different device configurations

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

The installed RAID controller for the "Adaptec RAID ASR8405" module is displayed as

follows in the BIOS:

Additional software and documentation

Refer to the following software documentation from the manufacturer:

●

Adaptec RAID Controller Quick Start Guide

The PDF file describes how you install the RAID controller and create a bootable RAID1

or RAID5 array. It also describes how you install the operating system and the controller

driver on the array.

●

Adaptec RAID Controller Installation and User Manual

The PDF file contains comprehensive information on installation and configuration of the

RAID adapter card and the connected devices.

●

Adaptec maxView Storage Manager User Manual

The PDF file contains comprehensive information on installation and use of Adaptec

maxView Storage Manager.

●

Command Line Utility User Guide

The PDF file contains the user manual for the command line utility program and

comprehensive information on the use of ARCCONF.

In order to use the software, the operating system must be password-protected. The

password must be assigned before the software is installed. In a correct installation, the

operating system password and RAID software password are the same.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды