Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 19 / 136

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

Safety Instructions

2.1

General safety instructions

WARNING

The installer of the system is responsible for the safety of a system in which the device is

integrated.
There is a risk of malfunction which could result in death or serious injury.

•

Ensure that only suitably qualified personnel perform the work.

Risk of physical injury

CAUTION

Risk of physical injury
The device is heavy, may fall down, injure persons and be damaged.

•

Use the handles on the front panel to carry and lift the device.

Risk due to electric shock

WARNING

Risk of electric shock
The on/off button and on/off switch do not fully disconnect the device from the mains.
There is also a risk of fire if the device or connecting lines are damaged.

•

Always fully disconnect the device from the mains voltage before performing work on

the device or when the device will not be used over an extended period of time.

•

For control cabinet mounting: If possible, use a central, easily accessible power

disconnector near the unit.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды