Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 26 / 136

Safety Instructions

2.2 Notes on use

SIMATIC IPC1047

Operating Instructions, 09/2018, A5E45118479-AA

CAUTION

Fault caused by I/O devices
The connection of I/O devices can cause faults in the device.
The result may be personal injury and damage to the machine or plant.

•

Only connect I/O devices which are approved for industrial applications in accordance

with EN 61000-6-2 and IEC 61000-6-2.

•

I/O devices that are not hotplug-capable may only be connected after the device has

been disconnected from the power supply.

NOTICE
Damage through regenerative feedback
Regenerative feedback of voltage to ground by a connected or installed component can

damage the device.
Connected or built-in I/Os, for example, a USB drive, are not permitted to supply any

voltage to the device.
Regenerative feedback is generally not permitted.

Note
When measuring the counter emf, remember the following:

•

The affected IPC must be switched off and the power plug must be plugged in.

•

All cables from the system must be connected to the IPC during measurement.

•

All other components in the plant must be active.

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды