Siemens SIMATIC IPC1047 Скачать руководство пользователя

Страница: 109 / 136

Technical specifications

8.4 Technical specifications

SIMATIC IPC1047
Operating Instructions, 09/2018, A5E45118479-AA

109

Mechanical ambient conditions

Vibration

Tested according to IEC 60068-2-6, 10 cycles

Storage/transport

5 Hz … 8.51 Hz: Amplitude 3.5 mm
8.51 … 500 Hz: Acceleration 1 g

Resistance to shock

Tested in accordance with IEC 60068-2-27, IEC 60068-2-29

Storage/transport

Half-sine: 250 m/s

, 6 ms, 1000 shocks per axis

Special features
Quality assurance

In accordance with ISO 9001

Motherboard

For more detailed information from the manufacturer, see section "Hardware description",

"Motherboard (Page 113)".

Drives

Hard disks

•

2.5", internal

•

3.5", internal (optional)

Solid State Drive

•

2.5" SATA, internal

RAID

SAS/SATA hardware

RAID controller (optional)

•

SAS/SATA RAID module PCIe x8, RAID 1, 5

•

Type: Adaptec 8405 (independent processor, 1024 MB DDR3 cache)

Parameter

•

1 × Mini SAS/SATA HD adapter (SFF-8643 for 4 drives)

•

Maximum theoretical controller data rate 12 Gb/s per port

•

Support of up to 256 SAS/SATA devices via SAS expander

•

Native 4K sector support for corresponding SAS/SATA disks

•

Supported RAID level: 0, 1, 1E, 5, 6, 10, 50, 60; Hybrid RAID 1 & 10

•

S.M.A.R.T. support

•

"Secure Boot" support for the UEFI BIOS

SAS Hardware RAID

controller (optional)

•

SAS RAID module PCIe x8, RAID 1, 5

•

Type: SAS 3008 Fusion MPT 2.5

Parameter

•

Mini SAS HD-Adapter (SFF8643 Two (x4))

•

8/4 ports, 12 Gbps

•

Up to 1024 SAS and SATA drives

•

8 Lanes PCIe 3.0

•

Supported RAID level: 0, 1, 1E, 10

•

Supports SSD, HDD, tape drives

Software RAID

•

Supported RAID level: 0, 1, 5, 10

Содержание SIMATIC IPC1047









































































































































Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды

Siemens SIMATIC IPC1047, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC IPC1047

Отзывы:

Похожие инструкции для SIMATIC IPC1047

Бренды по названию

Популярные бренды