Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 78

Страница: 78 / 196

Configuration / project engineering

5.3 Configuring the communication

ET 200pro FC

Operating Instructions, 07/2016, A5E01100763B AC

Address/ID

Setting an address in the I/O map

The start address configured here is accepted in the user program as the "LADDR" input

parameter for the blocks in the user program.

Image 5-18 Setting the address in the I/O map

Note
The input and output address area of the frequency converter must be the same.

Parameter

The application ID provides a unique means of identification and is assigned by the user.

Note
If the same application ID is entered for several frequency converters, they can be used

interchangeably. Frequency converters with the same application ID must be parameterized

in the same way. Only frequency converters with the same parameters may be used

interchangeably.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды