Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 142

Страница: 142 / 196

Series commissioning and operation

8.2 Series commissioning and replacement of the frequency converter

ET 200pro FC

142

Operating Instructions, 07/2016, A5E01100763B AC

WARNING

All the data interfaces, including the digital and analog interfaces, are reinitialized for the

series commissioning. This will interfere temporarily with data transfer or will cause the

digital outputs to switch over.
Before embarking on series commissioning, you must secure any dangerous loads.
To do this, proceed as follows:

•

Lower the load to the ground or

•

Secure the load using the motor holding brake.

Standard commissioning sequence with STARTER

Configure all frequency converters to be involved in standard commissioning with the

same application ID.

Commission the first frequency converter.

Upload from frequency converter to the PC: Frequency converter parameters are saved

on the PC.

Download from PC to the frequency converter: The saved parameters are transferred to

other frequency converters.

Note
In the case of a download with STARTER, all the necessary parameters (with the

exception of fail-safe parameters) will be downloaded to the frequency converter.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды