Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 21

Страница: 21 / 196

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

Description

2.1

The frequency converter

Description

The ET 200Pro FC is a compact frequency converter that is completely embedded in the

distributed I/O system of the ET 200pro. The individual components can be configured in

STEP 7 HW Config or integrated into other configuration systems using a GSD (device

master file).
The frequency converters are available in two versions:

●

Standard

●

Fail-safe

The frequency converter works with an input voltage of 3 AC 400 V 50/60 Hz and can be

used for 3-phase motors up to 1.1 KW, with temperature derating up to 1.5 KW.

Special features of the frequency converter

The power unit of the frequency converter feeds the braking energy from the motor back into

the line supply system. A braking resistor, which transforms energy accumulated during

regenerative operation into heat, is not necessary. The frequency converter can be operated

without a line reactor.

Commissioning and operation

The commissioning software STARTER is used for commissioning. It can be downloaded

from the Siemens homepage or ordered on a data carrier. It parameterizes the frequency

converter through a fieldbus or a point-to-point connection. You have the option of reading

the parameters for operating the frequency converter from the EEPROM of the frequency

converter or from a Micro Memory Card (MMC) that is inserted in the frequency converter. A

higher-level controller (e.g. SIMATIC S7) program is used to control the frequency converter.

Characteristics

●

Compact frequency converter in the SIMATIC ET 200pro system

●

Easy installation

●

Easy commissioning

●

Interconnection of signals using BICO technology

●

Selectable data sets

●

Fast current limitation (FCL) for trip-free operation

●

Energy recovery into line supply system

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды