Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 140

Страница: 140 / 196

Series commissioning and operation

8.2 Series commissioning and replacement of the frequency converter

ET 200pro FC

140

Operating Instructions, 07/2016, A5E01100763B AC

8.2

Series commissioning and replacement of the frequency converter

8.2.1

Application ID

The application ID is an important parameter for frequency converter standard

commissioning and replacement. It is specified in HW Config when the frequency converter

is configured (see Planning/Configuring) and saved in the PLC.
The application ID is designed to uniquely identify the frequency converter's parameter

assignment and to prevent frequency converters being swapped incorrectly.

Saving the application ID in the frequency converter

The very first time a connection is established between the PLC and frequency converter,

the application ID is accepted into the frequency converter and saved so that it is powerfail-

proof.
The frequency converter's application ID is also transferred and saved when the frequency

converter parameters are uploaded to an MMC or in STARTER.

Application ID during standard commissioning or replacement

When the frequency converter is replaced or after it has been parameterized by means of a

parameter download, the frequency converter receives the application ID from the PLC and

compares this value with the one saved in the frequency converter. If both values are

identical, the frequency converter is ready to run. If the values differ, the frequency converter

outputs fault F00395. In this case, you must check why the application IDs do not match.

Options for changing the application ID

There are two options for changing the application ID in the frequency converter:

●

Rejection of the parameter download

●

Acceptance of the parameter download

See "Fault codes during upload and download".
The application ID can, of course, be changed in the PLC too. Once the PLC has been

restarted, the modified application ID is transferred to the frequency converter.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды