Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 145

Страница: 145 / 196

Series commissioning and operation

8.3 Operational performance of the converter

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

145

8.3

Operational performance of the converter

Description

A normal power-up procedure refers to the converter starting up after it has been switched

off and on again, or after a power failure. It can be performed with or without an MMC.

Normal startup without MMC

Following a load cycle or a power failure, the frequency converter reads the parameters from

the EEPROM into the RAM.

Normal startup with MMC

The frequency converters have been designed so that they can automatically detect whether

an MMC is available. The level of interaction between the frequency converter and the MMC

is controlled by parameter P8458.
Possible settings for P8458 and its functions are specified below.

P8458 = 0:

Parameters not automatically downloaded from the MMC.

P8458 = 1:

Parameters automatically downloaded from the MMC once (when frequency converter

next powers up (factory setting)). After the download, P8458 will be set to 0.

P8458 = 2:

Parameters automatically downloaded from the MMC (if available) each time the fre-

quency converter powers up.

Once the automatic download is complete, parameter P8458 will be set to 0 (provided that it

had the value 1 before the download), thereby disabling any other automatic parameter

downloads.
If parameter P8458 is set to 1 or 2 and no MMC is available, the converter begins with the

EEPROM parameters without messages or fault codes.

Cyclic data exchange during operation

The frequency converter is controlled via the fieldbus by means of cyclic data traffic. The

frequency converter receives control commands and the frequency setpoint by way of

standard telegram 1.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды