Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 73

Страница: 73 / 196

Configuration / project engineering

5.3 Configuring the communication

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

Image 5-10 Setting the device-specific parameters

5.3.2

Generating a hardware configuration for PROFINET in the SIMATIC Manager

Description

The following example of an ET 200pro FC frequency converter with an "IM 154-4 PN HF"

interface module will be used to demonstrate how to generate a PROFINET configuration

with HW Config in the SIMATIC Manager. This will take place in three steps:

●

Parameterizing the PROFINET IO interface in SIMATIC S7

●

Equipping the ET 200pro station

●

Settings for the frequency converter

Note
Please refer to the "Interface modules" chapter in the manual entitled "ET 200pro

Distributed I/O System" for information on the interface modules.

Parameterizing the PROFINET IO interface in SIMATIC S7

The hardware configuration is used to parameterize the PROFINET IO interface. When a

CPU with an integrated DP interface or a DP communications processor is selected from the

hardware catalog, a PROFINET IO system is made available in the hardware configuration.

Once the parameters for the IO controller have been set, the slave - in this case, the

ET 200pro station - must be selected from the hardware catalog and positioned on the

PROFINET line. This is done by inserting an IM 154. The PROFINET address of the

ET 200pro station must also be specified in IM 154.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды