Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 138

Страница: 138 / 196

Series commissioning and operation

8.1 Transfer of the frequency converter parameter assignment

ET 200pro FC

138

Operating Instructions, 07/2016, A5E01100763B AC

8.1.5

Parameter transfer with PLC

Parameters can be uploaded and downloaded via fieldbus using the transfer mechanisms of

data set 47. For detailed information, refer to "Commissioning and Optimization".

8.1.6

Fault codes during upload and download

Fault codes

If a fault occurs during an automatic download procedure, the frequency converter returns to

the parameter set that was previously stored in the EEPROM and the following fault codes

are generated:

Error

Cause

Remedy/Test

F00061

No MMC inserted

•

MMC faulty?

•

Insert an MMC and attempt the upload/download

again.

F00062

MMC contents invalid

•

MMC faulty?

•

Parameter valid for this frequency converter?

F00063

MMC contents incompatible

•

MMC faulty?

•

Parameter set clone00.bin available on the MMC

•

Parameter valid for this frequency converter?

F00395

Different application ID after download

See below

Note
Once parameters have been uploaded from and downloaded to different frequency

converters, the parameter settings must be checked.
Downloading parameters from another frequency converter may cause a fault to occur with

F00063 output, if there are parameters that cannot be downloaded (check P0949 regarding

the (first) parameter number that cannot be downloaded).
If fault code F00061 or F00063 occurs during startup, it can only be cleared by shutting down

and restarting.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды