Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 169

Страница: 169 / 196

Appendix

A.1 Acceptance Log

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

169

Function test "Safely-Limited Speed" (SLS)

This test comprises the following steps:

Table A- 6

"Safely-Limited Speed" function (SLS)

No.

Description

Status

Initial state

•

Drive is "Ready to Run" (P0010 = 0)

•

No safety faults and alarms

•

r9772.4 = r9772.5 = 0 (SLS de-selected and inactive)

Operate the drive (if the machine permits it, at a higher speed than the pa-

rameterized safely-limited speed)

Check that the expected drive operates

Select SLS while issuing the traversing command

Check the following:

•

r9772.4 = 1 (SLS selected)

•

Drive speed decreases corresponding to the selected ramp time or SLS

mode (if required, use an oscilloscope)

•

After the parameterized safely-limited speed has been fallen below, the

speed remains below this limit
–

In SLS mode 1 à correct, must be no fault

–

In SLS mode 0 à LSTO (safety fault at ramping end)

–

In SLS mode 2 à LSTO (immediately)

•

r9772.5 = 1 (SLS active)

De-select SLS

Check the following:

•

No safety faults

•

r9772.4 = r9772.5 = 0 (SLS de-selected and inactive)

Check that the expected drive operates if so the following is tested:

•

The wiring between the control unit and power module is correct

•

Correct assignment, drive No. – inverter power module – motor

•

Correct functioning of the hardware

•

Correct wiring of the shutdown paths

•

Correct parameterization of the SLS function

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды