Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 64

Страница: 64 / 196

Configuration / project engineering

5.2 Installation of the hardware information in SIMATIC Manager

ET 200pro FC

Operating Instructions, 07/2016, A5E01100763B AC

5.2

Installation of the hardware information in SIMATIC Manager

5.2.1

Installation of a hardware support package (HSP)

The HSP (hardware support package) file defines the system environment of an ET 200pro

station. To be able to configure an ET 200pro with the HW Config tool, the relevant HSP file

must be installed first.

●

To do this, open the SIMATIC tool HW Config and go to "Install HW updates" in the

"Options" menu.

●

In the upper part of the window, select the source of the file (Internet or data carrier) and

click "Execute". A new window opens. The HSP files found are displayed in a drop-down

list box. Select the "ET 200pro" HSP and click "Copy" or "Download". You can then close

this window.

●

The copied HSP files will now be available in the drop-down list box of the window that

you initially opened. Select the HSP files to be installed from the list of available files in

the archive folder and click "Install". All STEP 7 applications will be closed automatically

and the selected HSP files installed.

The next time you open the HW Config tool, the ET 200pro station will be in the hardware

catalog under PROFIBUS DP.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды