Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 58

Страница: 58 / 196

Installation

4.8 Wiring in the ET 200pro system

ET 200pro FC

Operating Instructions, 07/2016, A5E01100763B AC

Motor cable

Motor cables up to 10 m long are available under the following order designation:

●

6ES7194-1LA01-0AA0 (1.5 m)

●

6ES7194-1LB01-0AA0 (3.0 m)

●

6ES7194-1LC01-0AA0 (5.0 m)

●

6ES7194-1LD01-0AA0 (10.0 m).

Longer lengths up to 15 m can be obtained from our service providers.

Note
A metallic connector housing must be used for connecting.
The shield of the motor cable must be connected through a large area of the motor

enclosure (for EMC reasons).

Power transfer

The power jumper connector is used to loop-through the main power from one frequency

converter/motor starter to the next frequency converter/motor starter.
The table below shows the assignment of the contacts:

Table 4- 8

Power jumper connectors

Male (pin)

Female (socket) Assignment

Phase L1

Phase L2

Phase L3

Not assigned

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды