Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 137

Страница: 137 / 196

Series commissioning and operation

8.1 Transfer of the frequency converter parameter assignment

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

137

The parameter download is triggered via STARTER, from the project file in the frequency

converter's RAM.

Note
When making use of this download procedure, you must bear in mind the following important

constraints:

•

During the download process, the frequency converter will not be able to respond to any

commands.

•

Once the download procedure is under way, there is no way of stopping it again.

•

If the data being downloaded are incompatible with the frequency converter, the relevant

parameters in the frequency converter's memory will revert to their default values.

•

In the event of an unsuccessful download, the frequency converter will not function as it

should.

When parameters are being downloaded from the PC to the frequency converter's

EEPROM, the LEDs will flash. If the frequency converter experiences a fault condition, the

fault is indicated by the LEDs (SF on, RY/RDY off). The download will be carried out

regardless.

Prerequisites

●

The download converter's power supply must be connected.

●

The download converter is in the "Ready to run" state.

Connect the STARTER PC to the download frequency converter via RS232 (point-to-point
connection, appropriate connecting cable required) or via fieldbus, press the online button

and perform the download using the ("Download project to target system") button.

The transferred parameters must then be saved in the frequency converter so that they are

powerfail-proof by pressing the

("RAM to ROM") button.

Remark
An online connection can only be established between the PC and frequency converter via

fieldbus if the following conditions are met:

●

The interface module of the ET 200 station is running in DPV1 mode.

●

The PC must be connected to the fieldbus directly.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды