Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 34

Страница: 34 / 196

Interfaces

3.1 Communication interfaces

ET 200pro FC

Operating Instructions, 07/2016, A5E01100763B AC

3.1.1

Optical interface

Description

The ET 200pro FC frequency converter has a serial optical communication interface with

USS protocol for commissioning using the STARTER commissioning software on a PC.

RS232/optical conversion is performed in the cable between the PC and the frequency

converter.
The following components are required:

●

PC with Windows 2000/Windows 2003 Server/Windows XP

●

STARTER commissioning software (version 4.1 or higher)

●

RS232 interface cable (Order No. 6RK1 922-2PB00).

3.1.2

Fieldbus interface (backplane bus)

Description

Communication between an ET 200pro station and the associated higher-level control

(e.g. SIMATIC S7) is established using the standardized PROFIBUS DP communication

protocol or PROFINET I/O. Communication within the ET 200pro system is performed over

the ET 200pro backplane bus. The ET 200pro IM 154 interface module creates the interface

between the two bus systems.

Communication data

The ET 200pro FC frequency converter is operated and controlled in normal process mode

via PROFIdrive profile 4.0 with standard telegram 1.
The PROFIdrive profile with the standard telegram 1 provides the following functionality:

●

Sending control words and setpoints with a fixed length to the drive

●

Receiving status words and actual values with a fixed length from the drive

●

Indicating drive faults through data record 47

●

Reading/writing parameters via data set 47.

Note
Parameter values are transferred in acyclic data exchange through data record 47.

Standard diagnostics

The frequency converter can be included in the standard diagnostics of S7.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды