Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 157

Страница: 157 / 196

Technical data

10.2 General ambient conditions

ET 200pro FC
Operating Instructions, 07/2016, A5E01100763B AC

157

10.2

General ambient conditions

The following conditions must be taken into account when installing a frequency converter:

Shocks and vibrations

The frequency converter must not be dropped, exposed to sudden shocks or installed in

surroundings where it might be exposed to regular vibrations.

Air pollution/water

The frequency converter must not be installed in areas where there are corrosive gases and

air pollution; however, it can be exposed to dust and splashwater (degree of protection

IP65).

Installation and cooling

Make sure that convection can take place freely in front of the frequency converter. In this

area there must be no devices which could obstruct or affect the convection.
A clearance of 35 mm must be kept above and below the components of the frequency

converter from other devices or components in order to ensure that convection can take

place unhindered.

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды