Siemens Simatic ET 200pro FC Скачать руководство пользователя страница 106

Страница: 106 / 196

Commissioning and optimization (software)

7.4 Commissioning of communication between the S7 CPU and the frequency converter

ET 200pro FC

106

Operating Instructions, 07/2016, A5E01100763B AC

Bit

Value

Meaning

Remarks

Fault present

Drive is faulty. A fault is present in the drive; it is, there-

fore, not operating and will switch back to the "Begin

start interlock" state once the fault has been success-

fully eliminated and acknowledged.

No fault

"Run down to stand-

still" not enabled

"Run down to stand-

still" enabled

"Run down to standstill" (OFF2) command present.

"Rapid stop" not ena-

bled

"Rapid stop" enabled "Rapid stop" (OFF3) command present.

Switch-on disabled

The drive is then only transferred to the "Switched on"

state when the "Do not run down to standstill" AND "No

rapid stop" commands, followed by "ON", are issued.

Switch-on not disa-

bled

Warning present

Drive still in operation; warning in service/maintenance

parameters; no acknowledgement; see interrupt pa-

rameter r2110.

No warning

No warning is present, or the warning has disappeared.

Speed deviation with-

in tolerance range

Setpoint/actual value deviation within tolerance range.

Speed deviation out-

side of tolerance

range

Master control re-

quested

The automation system is requested to assume control.

No control requested The master is not currently the master control.

Maximum frequency

reached or exceeded

Frequency converter output frequency is greater than

or equal to the maximum frequency.

Maximum frequency

not reached

Warning: Motor cur-

rent/torque limit

reached

Motor holding brake

enabled

Signal can be used to control a holding brake.

Motor data display overload status.

Motor overload

Clockwise rotation

Counter-clockwise

rotation

Converter overload

For example, current or temperature

Содержание Simatic ET 200pro FC





































































































































































































Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды

Siemens Simatic ET 200pro FC, Руководство по эксплуатации

Результаты поиска

Содержание Simatic ET 200pro FC

Отзывы:

Бренды по названию

Популярные бренды