Siemens D7-SYS Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 534

background image

Systemsoftware

2-4

System- and communication configuring D7-SYS - SIMADYN D

Edition 03.2001

•

Connections (I/O) with special functions have the following suffixes:

−

the dollar symbol "$" (connecting signals between CPUs),

−

the star symbol "*" (symbolic hardware addresses),

−

or the exclamation mark "!" (virtual addressing).

HWConfig or CFC automatically enter these suffixes. A function block
name may only appear once on a CPU. The name syntax and rules are
checked when entered.

Hardware modules and function block types are saved in libraries. The
required function blocks can be called-up from the libraries using
HWConfig or the CFC editor.

Several function block libraries can be used for each CPU. The "FBSLIB"
standard function block library is pre-assigned. It has over 200 function
blocks, whose functionality is sufficient for most applications. When
required, additional supplementary libraries can be imported for the
particular CPU. The libraries can be found in the directory
"step7\s7cfc\sdblocks\std (SIMADYN D) or ...\tdc (SIMATIC TDC)".

2.1.2 Configuring the hardware

HWConfig is used to configure the hardware of SIMATIC TDC/SIMADYN
D stations. A SIMATIC TDC/SIMADYN D station consists of a rack with
up to 20/8 CPUs and other hardware modules. When required, several
stations can be coupled with one another. The modules to be configured
can be selected from the modules in the HWConfig hardware catalog.
Racks, CPUs, I/O modules, coupling modules etc. can be selected.

HWConfig defines the system hardware configuration as result of

•

the rack used together with the defined bus structure (bus termination,

Daisy Chain),

•

the configured hardware modules inserted in the rack as well as

•

defining hardware-relevant information such as tasks, synchronization

etc.

2.1.2.1 The first step: Selecting the hardware modules

The following modules are available in the HWConfig hardware catalog:

Hardware

Description

Subracks

Various types depending on the slot number, bus
configuration, cooling etc.

I/O modules

Peripheral modules to input/output process signals
(analog-binary I/O, speed sensing signals etc.)

Expansion modules

Peripheral modules to input/output process signals.
They are used to achieve higher data rates by
bypassing the backplane bus, and are directly
connected to a CPU module.

Libraries

Configuring
SIMADYN D
stations

Short overview of
the hardware

«
...
43
44
45
46
47
...
»

Содержание D7-SYS























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D7-SYS

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: Jafar Страницы: 9

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: Echelon Страницы: 40

Бренд: Handicare Страницы: 56

Бренд: Samsung Страницы: 32

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: Salda Страницы: 16

Бренд: Samson Страницы: 48

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды