Siemens C541U Скачать руководство пользователя | Manualshive

Страница: 113 / 192

background image

Semiconductor Group

6-68

1999-04-01

On-Chip Peripheral Components

C541U

The bits of the endpoint buffer status registers indicate the status of the endpoint specific USB
memory buffers and allows setting of certain USB memory buffer conditions.

Endpoint Buffer Status Register EPBSn, n=0-4 (Address C2H)

Reset Value : 20H

Bit

Function

UBFn

USB buffer full
Bit UBFn indicates the status of the USB memory buffer for endpoint n.
USB read access:

If UBFn=0, the USB buffer for endpoint n is empty.
If UBFn=1, the USB buffer for endpoint n is not empty.

USB write access :

If UBFn=0, the USB buffer for endpoint n is not full.
If UBFn=1, the USB buffer for endpoint n is full.

CBFn

CPU buffer full
Bit CBFn indicates the status of the CPU memory buffer for endpoint n.
CPU read access:

If CBFn=0, the CPU buffer for endpoint n is empty.
If CBFn=1, the CPU buffer for endpoint n is not empty.

CPU write access:

If CBFn=0, the CPU buffer for endpoint n is not full.
If CBFn=1, the CPU buffer for endpoint n is full.

DIRn

Direction of USB memory access
Bit DIRn indicates the direction of the last USB memory access for endpoint n.
If DIRn=0, the last data flow for endpoint n was from host to CPU.
If DIRn=1, the last data flow for endpoint n was from CPU to host.

ESPn

Enable status phase
If bit ESPn is set, the next status phase of endpoint n will automatically be
acknowledged by an ACK except the endpoint n is stalled. If the status phase was
successfully completed, bit ESPn is automatically reset by hardware and no status
interrupt request (STI) is generated.
If the CPU detects a corrupted control transfer (endpoint 0), bit STALL0 should be
set by software instead of bit ESP0 in order to indicate an error condition which
cannot be recovered by the USB device itself.
Note : bit EPSn can only be set by software. Any read operation of register EPBSn
returns ESPn=0.

SETRDn

Set direction of USB memory buffer to read
Bit SETRDn is used to predict the direction of the next USB access for endpoint n
as an USB read access. A faulty prediction causes no errors since the USB
module determines the real direction. A change in the data direction is only
executed, if both USB memory buffers are empty. SETRD cannot be set together
with CLREPn because a change of bit DIRn during a transfer is not allowed.
Note : bits SETRDn and SETWRn must not be set at a time.

MSB

LSB

EPBSn

UBFn

CBFn

DIRn

ESPn SETRDn SETWRn CLREPn DONEn

7

6

5

4

3

2

1

0

Bit No.

r

r

r

w

w

w

w

w

C2H

«
...
111
112
113
114
115
...
»

Содержание C541U

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для C541U

ControlMaster CM15

Бренд: ABB Страницы: 28

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: Abicor Binzel Страницы: 8

Бренд: ECKELMANN Страницы: 178

Бренд: H3C Страницы: 17

Бренд: H3C Страницы: 32

Бренд: Elby Designs Страницы: 4

Бренд: Woodward Страницы: 32

Бренд: Vageo Страницы: 2

Бренд: DirectConnect Страницы: 2

Бренд: R-Tec Страницы: 14

Бренд: Tescom Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды