manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке


Поделиться
Скачать
background image

Assembly Guide for PRS Alpha and Standard Tools • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 5

Table of Contents (cont’d)

Position Motors on Tool .............................................................................................................. 7-4

Section 8. Wire and Cable Routing ..................................................................................................... 8-1

Hardware .................................................................................................................................... 8-1
Cable Routing Strategy .............................................................................................................. 8-1

Spindle Power Cable ............................................................................................................ 8-1
Motors and Signal Cables .................................................................................................... 8-1

Spindle Fan Cable Installation .................................................................................................... 8-2
Proximity Switch Installation ...................................................................................................... 8-2
Y Proximity Switch ..................................................................................................................... 8-2
Z Zero Plate Assembly ............................................................................................................... 8-3
Route Wiring ............................................................................................................................... 8-4
Mount Auxiliary Emergency Stop Switch ................................................................................... 8-4
Route Wiring (cont’d) .................................................................................................................. 8-5
X Proximity Switch ...................................................................................................................... 8-5
Route Wiring (cont’d) .................................................................................................................. 8-6
Pneumatic Air Hoses .................................................................................................................. 8-6
Route Spindle Cable ................................................................................................................... 8-7
Cable Checklist .......................................................................................................................... 8-7

Y Cable Carrier ..................................................................................................................... 8-7
Through Center of Gantry Beam .......................................................................................... 8-7
X Cable Carrier ..................................................................................................................... 8-7

Section 9. Control Box Installation ...................................................................................................... 9-1

Introduction ................................................................................................................................ 9-1

Section 10. Software Installation ....................................................................................................... 10-1

Introduction .............................................................................................................................. 10-1
Hardware .................................................................................................................................. 10-1
Computer Recommendations .................................................................................................. 10-2
Computer Configuration ........................................................................................................... 10-2
Install ShopBot 3 Control Software and VCarve Pro Software ................................................ 10-2
Software Overview ................................................................................................................... 10-2
Engage Pinions with Rack ........................................................................................................ 10-3
Connect ShopBot to Computer................................................................................................ 10-3

USB Communication Cable ................................................................................................ 10-3

Load the Settings File ............................................................................................................... 10-4
Install Control Box Firmware .................................................................................................... 10-4
ShopBot Control Software Familiarization ............................................................................... 10-6

Easy and Full Modes .......................................................................................................... 10-6
Full Display Overview ......................................................................................................... 10-6
ShopBot Command Format ............................................................................................... 10-7

Movement Testing .................................................................................................................... 10-7
X Proximity Switch .................................................................................................................... 10-7
Set Stop Block Positions .......................................................................................................... 10-8
Check Y-Axis Proximity Switches ............................................................................................. 10-8
Mount Z Zero Plate Assembly .................................................................................................. 10-8

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

C&K systems Securit 800L Specfications preview
Securit 800L
Бренд: C&K systems Страницы: 2
Vacon NX series Maintenance Manual preview
NX series
Бренд: Vacon Страницы: 64
JDS Uniphase SK Series User Manual preview
SK Series
Бренд: JDS Uniphase Страницы: 27
Danfoss EH Series Service Manual preview
EH Series
Бренд: Danfoss Страницы: 20
OEG KMS Manual preview
KMS
Бренд: OEG Страницы: 168
Canarm MC Series Installation Manual preview
MC Series
Бренд: Canarm Страницы: 3
Vasco RF User And Installation Manual preview
RF
Бренд: Vasco Страницы: 32
Abra AK-10 User Manual preview
AK-10
Бренд: Abra Страницы: 16
SAI Connect Operation Manual preview
Connect
Бренд: SAI Страницы: 16
Hable One Starting Manual preview
One
Бренд: Hable Страницы: 3
Eaton A201 Instruction Leaflet preview
A201
Бренд: Eaton Страницы: 6
FAAC E124 Manual preview
E124
Бренд: FAAC Страницы: 32
ICP DAS USA I-7000 Series Quick Start Manual preview
I-7000 Series
Бренд: ICP DAS USA Страницы: 6
Jabra Link 14201-10 How Do preview
Link 14201-10
Бренд: Jabra Страницы: 4
Maguire Products GRAVIMETRIC AUGER FEEDER MGF-ST Instruction Manual preview
GRAVIMETRIC AUGER FEEDER MGF-ST
Бренд: Maguire Products Страницы: 47
Magtrol DSP7000 User Manual preview
DSP7000
Бренд: Magtrol Страницы: 160
Omega 21032 Operating Instructions Manual preview
21032
Бренд: Omega Страницы: 44
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Бренд: Taco Electronic Solutions Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды