manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке

Поделиться
Скачать
ShopBot PRSalpha Скачать руководство пользователя страница 76

Section 8: Wire and Cable Routing • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 8-6

Rotate bolt so the three prongs are oriented as shown in the image at left. 
This ensures the cable will route cleanly.

Make sure the switch to target clearance is still 1/32” – 1/16” (1-2mm), and 
snug both nuts with a 1/2” wrench.

Connect the X-axis proximity switch cable (marked with red tape) by 
threading the nut onto the connector on the back of the switch.

Uncoil the cable. 

Route Wiring (cont’d)

Run cables inside lip of left hand gantry plate, and zip tie 
cables to e-chain bracket.

Snap open e-chain gates, and run cables through e-chain.  
Do not snap all e-chain gates shut.

Zip tie cables at both ends of e-chain.

Continue using zip ties along the rest of the cables, approxi-
mately 3-6” apart.

Note:

 Spindle power cable is the orange cable in picture. 

This is not installed until p. 8-7.

Pneumatic Air Hoses

Certain applications such as the automatic tool changer (ATC), pneumatic assist, and air drill have one 
or more air hoses that will route through the cable carrier.

To install an air drill, refer to PRS alpha Air Drill manual located at http://www.shopbottools.com/Shop-
BotDocs/files/PRSalphaAirDrillDV.pdf. 

To install an ATC, refer to ATC Installation manual located at http://www.shopbottools.com/ShopBot-
Docs/files/ATCCombinedManual.pdf.

To install a pneumatic assist, refer to Installing a Z-axis pneumatic assist manual located at http://
www.shopbottools.com/ShopBotDocs/files/PneumaticAssistInstall.pdf. 

Route all air hoses before closing all gates.

Secure Y-axis cable gates.

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды