manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке

Поделиться
Скачать
ShopBot PRSalpha Скачать руководство пользователя страница 23

Section 2: Table Assembly • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 2-9

Note: 

This image shows the approximate T-nut locations for the upper table supports and cross sup-

ports for the PRSalpha 96-48 table set up. A table configuration with more table legs or cross supports 
will require additional T-nuts as indicated on table drawing. Two are needed for every component.

Mount Table Supports and Gussets to Table Legs

Orient the gusset as in the illustration (the flange 
faces the table leg).  Use the same 1/2” hard-
ware (hex bolt and flat washer on one side—flat 
washer, lock washer, and hex nut on the back 
side) to secure the 

bottom

 corner of each 

gusset. When a gusset is properly oriented, the 
gusset flange will rest against the table leg, hold-
ing it in position. Tighten bottom bolt, but not the 
top one.

If performing this step without assistance, mount the middle 
two bolt locations of the table support to the gusset to hold 
the table support in place while the remaining hardware is 
installed.

Note: 

The front table support is the one with the ShopBot 

decal.

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды