ShopBot PRSalpha Скачать руководство пользователя | Manualshive

Страница: 43 / 100

background image

Section 4: Cable Carrier Installation • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 4-5

Install Upper Y-Chain Bracket

On the back left side edge of the YZ car there are two ¼-20 holes.
Note the location of the bracket in relation to the Z motor on the YZ
car. Align holes in the longest tab of the upper Y-chain bracket with
the tapped holes of the YZ car. Use the ¼-20 screws, lock washers,
and flat washers to tighten the bracket securely to the YZ car.

Mount Cable Carrier to Lower Y Bracket

Align the counter sunk holes in the cable carrier with the holes in the
top of the lower Y bracket. Loosely start the 10-32 x ¾ screws into
the lower Y chain bracket.

Mount Cable Carrier to Upper Y Bracket

Align the counter sunk holes in the cable carrier with the
holes in the top tab of the upper Y bracket. Use screws, flat
washers, lock washers, and hex nuts to secure the end link to
the Y upper bracket.

Install cable tie brackets. These will be used to secure cables along the
top of the gantry after they have been routed. Drop T-section into gantry
slot at desired position. Twist T-section 90 degrees to lock in place.

Position cable tie brackets evenly between cable carriers and end plate.

«
...
41
42
43
44
45
...
»

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

Бренд: S-COM Страницы: 400

Бренд: LaserBit Страницы: 69

Бренд: Lawler Страницы: 5

Бренд: National Instruments Страницы: 78

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: Bender Страницы: 28

Бренд: Hirschmann Страницы: 48

Бренд: Nibe Страницы: 84

Бренд: IBC control Страницы: 16

HmIP-FAL230-C10

Бренд: HomeMatic Страницы: 42

Бренд: Vestil Страницы: 8

Бренд: e-survey Страницы: 12

Бренд: Waeco Страницы: 168

Бренд: CALEFFI Страницы: 8

Бренд: Roger Страницы: 2

GA Industries FIGURE 927

Бренд: Vag Страницы: 5

Бренд: C&K systems Страницы: 4

SW-HBT4K-C6-4X4E

Бренд: Avenview Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды