ShopBot PRSalpha Скачать руководство пользователя

Страница: 13 / 100

Section 1: Setup and Assembly Overview • May 2, 2016

page 1-3

Terms to Know

This is only a quick overview to get started. For each assembly section, there will be a visual guide
with all parts and hardware clearly labeled.

Major Components:

The base of the machine is referred to as the

table

frame

The two long aluminum extrusions on each side
are called

table sides

. Atop the sides are the

rails

which create the path of travel for the X-axis.

The table sides and rails are included in the long
cardboard package secured to the top of the crate.

The assembly that rides along the table sides is
called the

gantry

The gantry consists of an extruded aluminum
beam, which has been fitted with V rails (for wheel
bearings) and gear rack. This forms the path of
travel for the Y-axis.

The blue plates on either side of the gantry are
referred to as

end plates

The

YZ car

moves across the gantry, and controls

the height of the

cutter head

(either a router or

high-speed spindle, depending on the tool).

Содержание PRSalpha























































































Результаты поиска

Содержание PRSalpha

Отзывы:

Похожие инструкции для PRSalpha

Бренды по названию

Популярные бренды

ShopBot PRSalpha, Инструкция по сборке

Результаты поиска

Содержание PRSalpha

Отзывы:

Похожие инструкции для PRSalpha

Бренды по названию

Популярные бренды