manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке


Поделиться
Скачать
background image

Assembly Guide for PRS Alpha and Standard Tools • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 6

Table of Contents (cont’d)

Secure Cables .......................................................................................................................... 10-9

Section 11. Secure Table and Spoil Board ........................................................................................ 11-1

Introduction .............................................................................................................................. 11-1
Hardware .................................................................................................................................. 11-1
Base Layer ................................................................................................................................ 11-1
Spoilboard ................................................................................................................................ 11-2

Section 12. Setup and Fine Tuning ................................................................................................... 12-1

Check Inputs and Outputs ....................................................................................................... 12-1
Machine Orientation ................................................................................................................. 12-2
Optional Axes ........................................................................................................................... 12-2
Setting Up RPM Control ........................................................................................................... 12-3
System Check .......................................................................................................................... 12-4

Check Movement ............................................................................................................... 12-4
Check Stops and Targets ................................................................................................... 12-4
Check Limit Switches ......................................................................................................... 12-4
Check Movement Distance ................................................................................................ 12-5
Test X-Axis Distance ........................................................................................................... 12-5
Test Y-Axis Distance ........................................................................................................... 12-5
Test Z Zero Function ........................................................................................................... 12-5
Proximity Switch Targets .................................................................................................... 12-5

ShopBot Setup ......................................................................................................................... 12-6

Z Zero Plate ........................................................................................................................ 12-6
XY Zeroing Point ................................................................................................................. 12-6

Fine Tune Setup ........................................................................................................................ 12-7

Square the Spindle ............................................................................................................. 12-7
Secure Mounting Screws.................................................................................................... 12-7
Test Movement Distance .................................................................................................... 12-7

Install Push Bars ....................................................................................................................... 12-7
Install Dust Foot........................................................................................................................ 12-7
Install End Caps........................................................................................................................ 12-7

Resources ......................................................................................................................................... 12-7

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

ABB REC650 ANSI Applications Manual preview
REC650 ANSI
Бренд: ABB Страницы: 370
ABB EAN823 Instructions Manual preview
EAN823
Бренд: ABB Страницы: 17
ABB COM600 series User Manual preview
COM600 series
Бренд: ABB Страницы: 104
ABB AC 800M Library Object Style Manual preview
AC 800M
Бренд: ABB Страницы: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Бренд: ABB Страницы: 42
Jafar 3500 Operating Manual preview
3500
Бренд: Jafar Страницы: 9
Samsung SPC-6000 Quick Setup Manual preview
SPC-6000
Бренд: Samsung Страницы: 6
Samsung SyncMaster VC240 Reference Manual preview
SyncMaster VC240
Бренд: Samsung Страницы: 39
Samsung MWR-WE10N Manual preview
MWR-WE10N
Бренд: Samsung Страницы: 32
Samsung iDCS500 Manual preview
iDCS500
Бренд: Samsung Страницы: 91
Samsung iDCS500 User Manual preview
iDCS500
Бренд: Samsung Страницы: 80
Yardney Synergy Quick Start Manual preview
Synergy
Бренд: Yardney Страницы: 8
Cansec H1000 Installation Manual And Instructions For Use preview
H1000
Бренд: Cansec Страницы: 45
Cansec CP40 Installation Manual preview
CP40
Бренд: Cansec Страницы: 43
Cansec MAP2 Installation Manual preview
MAP2
Бренд: Cansec Страницы: 32
QUALITY LIFTS Q10 Installation, Operation & Maintenance Manual preview
Q10
Бренд: QUALITY LIFTS Страницы: 13
DAB ACTIVE DRIVER M/M 1.1 Programming Manual preview
ACTIVE DRIVER M/M 1.1
Бренд: DAB Страницы: 10
d&b audiotechnik 10D Quick Start Manual preview
10D
Бренд: d&b audiotechnik Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды