manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке

Поделиться
Скачать
ShopBot PRSalpha Скачать руководство пользователя страница 45

Section 4: Cable Carrier Installation • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 4-7

Install the X-Axis Trough:  6” Z-Axis

Position the first cable carrier trough so the holes closest to the 
edges are over the inside holes in the trough brackets.

Fasten the trough to the bracket using 1/4” flat head screws, 
flat washers, and nylock nuts. Leave these loose until range of 
motion is checked.

Repeat installation of the other trough piece, using the outer 
holes on the bracket.

For models that need extended lengths of trough (longer than 96” 
in the X), use the second set of holes in the cable carrier bracket 
to butt the trough sets together.

Machines with 12” and 24” Z-Axis

Machines with two side rails require alternate mounting brackets for the X-axis trough brackets. The 
brackets are attached to the outside of the lower frame rail with T-nuts.

Slide a 5/16-18 T-nut into each of the top three grooves on the lower table side extrusion, with the 
flanged face of the nuts facing towards the inside of the table. Loosely thread a 5/16-18 x 3/4 Button 
Head Screw and 5/16 Lock Washer through the trough bracket into each T-nut, as shown below.

Repeat this step with the remaining bracket(s) (extended tables may have 3-4 brackets). Keep the 
mounting hardware loose so the brackets can slide along the table side in order to be moved into the 
proper position. 

Attach the trough to the brackets in the same manner as for the tools with the 6” Z.

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды