manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке

Поделиться
Скачать
ShopBot PRSalpha Скачать руководство пользователя страница 57

Section 6: Spindle and VFD Installation • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 6-1

Section 6. VFD and Spindle Installation

Introduction

This section covers mounting the variable frequency display (VFD) and spindle.

If attaching a router instead of a spindle, refer to Installing and Removing Router document. This doc-
ument was provided with the tool, and can also be accessed at http://www.shopbottools.com/Shop-
BotDocs/files/RouterRemovalInstall.pdf.

If attaching Automatic Tool Changer (ATC), refer to ATC Installation Manual. This document was pro-
vided with the tool, and can also be accessed at http://www.shopbottools.com/ShopBotDocs/files/
ATCCombinedManual.pdf

VFD Installation

ShopBot Tools with spindles use a VFD to regulate input power and control rotation speed. There are 
two major body sizes, 10” and 16”, which are used depending on specific voltage and phases require-
ments. The supplied bracket will work for each size.

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды