manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке

Поделиться
Скачать
ShopBot PRSalpha Скачать руководство пользователя страница 47

Section 4: Cable Carrier Installation • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 4-9

Cable Carrier to Lower X Bracket

Open the first five access gates by inserting the tip of a 
flathead screwdriver into either side of the hinged access 
gate. Turn the screw driver approximately 1/4 turn in each 
direction until the side of the access gate releases.

Attach that end of the cable carrier to the holes located 3 1/2” 
(64mm) from the end of the trough and closest to the middle of the 
machine.

Use flat head 10-32 screws, flat washer, lock washer and nuts to 
attach the lower portion of the cable carrier to the trough.

Test Cable Carrier Mobility on Both Axes

Place the open access gates close to their clasps to keep them from snagging and breaking off while 
testing the carrier mobility.  Move the X-axis back and forth the full extent of travel. The cable carrier 
should not feel as though it is binding or under tension. If need be, adjust the trough brackets slightly 
along the table side (X-axis.) Finishing by tightening the 5/16 button head screws holding the brackets 
to the table.  The lower end plate on the Y-axis can also be adjusted slightly if the Y-axis binds.

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды