manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке


Поделиться
Скачать
background image

Assembly Guide for PRS Alpha and Standard Tools • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 4

Table of Contents (cont’d)

Y-Axis Cable Carrier ................................................................................................................... 4-4
Mount the Lower Y Bracket ........................................................................................................ 4-4
Install Upper Y-Chain Bracket .................................................................................................... 4-5
Mount Cable Carrier to Lower Y Bracket ................................................................................... 4-5
Mount Cable Carrier to Upper Y Bracket ................................................................................... 4-5
X-Axis Cable Carrier ................................................................................................................... 4-6
Install Trough Brackets for ShopBots with 6” Z’s ....................................................................... 4-6
Install the X-Axis Trough: 6” Z-Axis ............................................................................................ 4-7
Machines with 12” and 24” Z-Axis ............................................................................................. 4-7
Install the Upper X Cable Carrier Bracket .................................................................................. 4-8
Cable Carrier to Upper X Bracket ............................................................................................... 4-8
Cable Carrier to Lower X Bracket ............................................................................................... 4-9
Test Cable Carrier Mobility on Both Axes ................................................................................... 4-9
X-Axis Cable Carrier Configurations ......................................................................................... 4-10

Section 5. Control Box Installation ...................................................................................................... 5-1

Introduction ................................................................................................................................ 5-1
Hardware .................................................................................................................................... 5-2
Installation .................................................................................................................................. 5-4
Alternate Mounting for 12” and 24” Z-Axis Models ................................................................... 5-5

Section 6. VFD Installation and Spindle .............................................................................................. 6-1

Introduction ................................................................................................................................ 6-1
VFD Installation ........................................................................................................................... 6-1
Hardware .................................................................................................................................... 6-2
Determining the VFD Model ....................................................................................................... 6-2
Voltage Amperage ...................................................................................................................... 6-3
Mounting the 10” VFD ................................................................................................................ 6-3
Mounting the 16” VFD ................................................................................................................ 6-4
Spindle Installation ..................................................................................................................... 6-5
Hardware .................................................................................................................................... 6-5
Lower the Z-Axis Extrusion ........................................................................................................ 6-6
Spindle Mounting Plate .............................................................................................................. 6-6
Attach Spindle ............................................................................................................................ 6-7
Replace Stop Screw ................................................................................................................... 6-7
Section 6 Appendix: Table Leg Drawings ................................................................................... 6-8

6” Table Leg ....................................................................................................................... 6-8
12” Table Leg ..................................................................................................................... 6-9

Section 7. Mounting X- and Y-Axis Motors ......................................................................................... 7-1

Introduction ................................................................................................................................ 7-1
Hardware .................................................................................................................................... 7-2
Motors ........................................................................................................................................ 7-2
Mount Pinions to Motors ............................................................................................................ 7-2
Identify Motors............................................................................................................................ 7-3
Check Alignment of Pinions with Rack ...................................................................................... 7-3
Check Pinion/Rack Alignment .................................................................................................... 7-3
Adjust Pinions (If Required) ........................................................................................................ 7-3
Mounting Locations .................................................................................................................... 7-4

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

Yudian AI Series Operation Instruction Manual preview
AI Series
Бренд: Yudian Страницы: 26
Sanhua MDF Series Instructions preview
MDF Series
Бренд: Sanhua Страницы: 3
rav KT100 Operating Instructions Manual preview
KT100
Бренд: rav Страницы: 120
TCi 18055 Manual preview
18055
Бренд: TCi Страницы: 9
Daikin BRC1H61W Installation Manual preview
BRC1H61W
Бренд: Daikin Страницы: 46
Daikin BRC1H61W Installation Handbook preview
BRC1H61W
Бренд: Daikin Страницы: 26
Data Signs PTL Compact 2 Operation And Maintenance Manual preview
PTL Compact 2
Бренд: Data Signs Страницы: 23
Savant SKL-3040-00 Quick Reference Manual preview
SKL-3040-00
Бренд: Savant Страницы: 2
HEIDENHAIN ND 1300 Operating Instructions Manual preview
ND 1300
Бренд: HEIDENHAIN Страницы: 257
Omniflex Maxiflex M1434 Installation Manual preview
Maxiflex M1434
Бренд: Omniflex Страницы: 2
LCT HQ-TJ-901 Operation Manual preview
HQ-TJ-901
Бренд: LCT Страницы: 5
XP Metal Detectors DEUS II RC Quick Start Manual preview
DEUS II RC
Бренд: XP Metal Detectors Страницы: 4
Gardigo BAT HOUSE Instruction Manual preview
BAT HOUSE
Бренд: Gardigo Страницы: 12
Wavelength Electronics PTC5000 Datasheet And Operating Manual preview
PTC5000
Бренд: Wavelength Electronics Страницы: 17
ICP DAS USA tM-P3R3 Quick Start Manual preview
tM-P3R3
Бренд: ICP DAS USA Страницы: 6
IEI Technology IVC-168G Quick Installation Manual preview
IVC-168G
Бренд: IEI Technology Страницы: 14
Vega VEGATOR 131 Operating Instructions Manual preview
VEGATOR 131
Бренд: Vega Страницы: 28
WATSON W91 Series Installation, Operation & Maintenance Instructions Manual preview
W91 Series
Бренд: WATSON Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды