ShopBot PRSalpha Скачать руководство пользователя

Страница: 73 / 100

Section 8: Wire and Cable Routing • May 2, 2016

page 8-3

Thread proximity switch into hole until it rests on the target. Back it out
1 to 2 turns so there is a 1/32” – 1/16” (1-2mm) gap between them.

Tighten nuts and connect the Y-axis proximity switch cable (marked
with blue tape).

For best cable routing, the orientation of the three pins in the switch
should resemble an arrow pointing downward.

Screw Y cable carrier onto Y proximity switch.

Route cable up the left side of the YZ car and through the YZ plate.

Secure cable to the YZ plate flange using zip ties in the pre-drilled holes.

Z Zero Plate Assembly

The Z zero plate assembly allows for accurately calibrating the height of the Z
axis before cutting.

All of the Z zero plate components are packed in a plastic bag inside the box
of accessories.

Locate 30’ gray cable and the two black 3mm screws in the Z zero
assembly kit.

Attach the gray Wago connector to the upper right side of the YZ
plate, as shown in this image.

Note:

The white plastic hooked piece indicated by the arrow is

known as a Wago tool. It’s used as a fulcrum to release wires from
Wago connector terminals. Store it in a safe place.

Содержание PRSalpha























































































Результаты поиска

Содержание PRSalpha

Отзывы:

Похожие инструкции для PRSalpha

Бренды по названию

Популярные бренды

ShopBot PRSalpha, Инструкция по сборке

Результаты поиска

Содержание PRSalpha

Отзывы:

Похожие инструкции для PRSalpha

Бренды по названию

Популярные бренды