ShopBot PRSalpha Скачать руководство пользователя | Manualshive

Страница: 77 / 100

background image

Section 8: Wire and Cable Routing • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 8-7

Route Spindle Cable

Route orange spindle cable from the VFD, under the table, through the X-axis
e-chain, through the Y-axis e-chain, and into the spindle.

Keep spindle cable separate from the others, as it is capable of generating
noise, which could affect the machine electronics.

Close all e-chain gates.

Route cables under table to control box. If installing (or planning to install) 10”
table extension, ensure an extra 10” of slack is available in the cables.

Cable Checklist

Note:

In both cable carriers, keep the spindle/router power cord separate from the other cables. This

will prevent electrical interference that may cause connection problems during use.

All wires and cables from the gantry will be carried in the X and Y axis cable carriers. Use this checklist
to inspect cables before closing the cable carrier.

Y Cable Carrier

_____ Spindle or router power cord

_____ Spindle fan cable (if applicable)

_____ Y motor cable

_____ Z motor cable

_____ Y-axis proximity switch

_____ Z-axis proximity switch (optional, stock for ATC tools only)

_____ Z zero plate and auxiliary function wire

Through Center of Gantry Beam

_____ X2 motor cable (route through the hole in the center of the gantry beam)

_____ Emergency stop switch (if mounted in predrilled location on end plate near X2 motor)

X Cable Carrier:

All of the above, plus

_____ X1 motor cable (routed above the upper X cable carrier bracket)

_____ X-axis proximity switch

_____ Pneumatic air hoses (for ATC tools and optional air drills or pneumatic assists)

«
...
75
76
77
78
79
...
»

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

Бренд: Bartlett Страницы: 30

Бренд: GE Страницы: 8

Бренд: Panasonic Страницы: 15

Бренд: Panasonic Страницы: 42

Бренд: EasyIO Страницы: 12

Бренд: RMG Страницы: 6

Бренд: National Instruments Страницы: 2

Бренд: Wang Страницы: 68

Бренд: NAVITAS Страницы: 14

Бренд: Madison AV Страницы: 2

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренд: ICP DAS USA Страницы: 8

TLX-7000-FLRAILKIT

Бренд: IDEAL Страницы: 10

Бренд: WAC Страницы: 5

Бренд: DeLaval Страницы: 102

Бренд: Harman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды