ShopBot PRSalpha Скачать руководство пользователя страница 71

Страница: 71 / 100

Section 8: Wire and Cable Routing • May 2, 2016

page 8-1

Section 8. Wire and Cable Routing

Hardware

Part

Quantity

ShopBot part number

Notes

Cable tie brackets

003062

Proximity switch

002740

Proximity switch cable

002739

Z zero plate and wire kit

14524

Emergency stop button

002723

PRS Standard

E-stop

000777

PRS Alpha

Cable Routing Strategy

Cable and wire routing will generally follow these steps. Greater detail is provided after this overview:

Spindle Power Cable

•

Uncoil spindle power cable.

•

Run cable from VFD under table to X cable carrier.

•

Secure to one side of carrier so motor and signal cables can be run on other side of carrier.

•

Run cable to Y cable carrier.

•

Remain on opposite side of signal and motor wires.

•

Arch cable over top of YZ car and install on spindle.

•

Take up slack in cable moving from Y to X cable carriers and secure cable with zip ties.

Motors and Signal Cables

•

Install the source if it is not already installed.

•

Unroll cable to ensure even feeding and minimize coiling.

•

Secure cable with zip ties along the route to the proper location.

•

Route to first cable carrier (usually Y) and secure in place with two closed gates.

•

Route all applicable cables through Y cable carrier.

•

Relieve tension on Y cable carrier and secure wires at either end with zip ties.

•

Route bundle from Y cable carrier to X cable carrier.

•

Route other cables into X cable carrier (X motor cables, X prox switch, and emergency stop).

•

Secure cables between cable carriers with zip ties.

•

Organize and relieve tension on cables in X cable carrier and secure with zip ties.

•

Route cables under table.

Содержание PRSalpha























































































Результаты поиска

Содержание PRSalpha

Отзывы:

Бренды по названию

Популярные бренды

ShopBot PRSalpha, Инструкция по сборке

Результаты поиска

Содержание PRSalpha

Отзывы:

Бренды по названию

Популярные бренды