manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке


Поделиться
Скачать
background image

Assembly Guide for PRS Alpha and Standard Tools • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 3

Table of Contents

General Safety and Precautions ..............................................................................................................7
PRS Quick-Start Process Flow ...............................................................................................................8
Main Parts of PRSalpha ..........................................................................................................................9
Section 1. Setup and Assembly Overview .......................................................................................... 1-1

Electrical Precautions ................................................................................................................. 1-1
Safety.......................................................................................................................................... 1-1
Unpacking the Crate................................................................................................................... 1-2
Terms to Know ............................................................................................................................ 1-3
Major Components ..................................................................................................................... 1-3

Section 2. Table Assembly .................................................................................................................. 2-1

Introduction ................................................................................................................................ 2-1
Hardware .................................................................................................................................... 2-2
Marking the Rails ........................................................................................................................ 2-3
Mount Table Levelers to Legs..................................................................................................... 2-4
Install Table Legs ........................................................................................................................ 2-4
Table Sides for 12” and 24” Z-Axis Configurations .................................................................... 2-6
Stabilize with Lower Table Supports .......................................................................................... 2-7
Connect Side Assemblies .......................................................................................................... 2-7
Install Middle Lower Cross Support ........................................................................................... 2-8
Insert T-Nuts in Bottom Slot ....................................................................................................... 2-8
Mount Table Supports and Gussets to Table Legs .................................................................... 2-9
Mount Table Supports and Cross Supports to Rails ................................................................ 2-11
Install Cross Supports .............................................................................................................. 2-11
Level and Square the Table ...................................................................................................... 2-12
Level the Front Table Side ........................................................................................................ 2-12
Level the Rear Table Side ......................................................................................................... 2-13
Square the Rear Table Side ...................................................................................................... 2-14
Install the Rails ......................................................................................................................... 2-15
Adjust the Front Rails ............................................................................................................... 2-16

Section 3. Gantry Installation .............................................................................................................. 3-1

Introduction ................................................................................................................................ 3-1
Hardware .................................................................................................................................... 3-2
Install Gantry............................................................................................................................... 3-3
Adjust the Rails ........................................................................................................................... 3-3
Fine Tune the Rail Level .............................................................................................................. 3-4
Install the YZ Car ........................................................................................................................ 3-4
Test and Adjust Wheel Tension ................................................................................................... 3-5
Mount the X-Axis Stop Blocks and Proximity Targets ................................................................ 3-6
Adjust the Y-Axis Stop Blocks and Sensor Targets .................................................................... 3-7

Section 4. Cable Carrier Installation .................................................................................................... 4-1

Introduction ................................................................................................................................ 4-1
Hardware .................................................................................................................................... 4-2
Prepare the Cable Carriers ......................................................................................................... 4-3
Reversing the End Links ............................................................................................................. 4-3

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

ABB Relion 670 series Applications Manual preview
Relion 670 series
Бренд: ABB Страницы: 760
ABB 650 series Engineering Manual preview
650 series
Бренд: ABB Страницы: 128
Panasonic TY-RM50VW Operating Instruction preview
TY-RM50VW
Бренд: Panasonic Страницы: 72
Panasonic CZ-RTC5 Operating Instructions Manual preview
CZ-RTC5
Бренд: Panasonic Страницы: 45
Panasonic CZ-RWSU3 Operating Instructions Manual preview
CZ-RWSU3
Бренд: Panasonic Страницы: 24
1Control Solo Technical Sheet preview
Solo
Бренд: 1Control Страницы: 8
EasyIO FG Series User Manual preview
FG Series
Бренд: EasyIO Страницы: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Бренд: RMG Страницы: 6
Vasco RF User And Installation Manual preview
RF
Бренд: Vasco Страницы: 32
Abra AK-10 User Manual preview
AK-10
Бренд: Abra Страницы: 16
SAI Connect Operation Manual preview
Connect
Бренд: SAI Страницы: 16
Hable One Starting Manual preview
One
Бренд: Hable Страницы: 3
Baader Planetarium Steeldrive II Manual preview
Steeldrive II
Бренд: Baader Planetarium Страницы: 7
Beaphar RabbitComfort Product Information preview
RabbitComfort
Бренд: Beaphar Страницы: 2
Harman AMX JPK-1300 Quick Start Manual preview
AMX JPK-1300
Бренд: Harman Страницы: 2
T-Link TL300 Quick Install Manual preview
TL300
Бренд: T-Link Страницы: 3
Jedia JMA-5104 Operating Instructions Manual preview
JMA-5104
Бренд: Jedia Страницы: 12
JED Micro T470 User And Installation Manual preview
T470
Бренд: JED Micro Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды