ShopBot PRSalpha Скачать руководство пользователя

Страница: 72 / 100

Section 8: Wire and Cable Routing • May 2, 2016

page 8-2

Finishing

•

Close or partially close all cable carrier gates.

•

Move tool along each axis looking for even movement and binding.

•

If binding or height tensions occurs, relieve tension and re-secure cables as needed.

•

Clip off all zip tie ends using wire snips.

Spindle Fan Cable Installation

Uncoil cable.

Connect plug and tighten screw, locking it into place.

Zip tie the cable to the spindle power cable up to the point
where it would enter the Y carrier.

Proximity Switch Installation

Locate the proximity switches and the corresponding cables.

The cables are marked with colored tape at both ends for ease of
identification.

Blue indicates Y-axis. Red indicates X-axis.

Note:

The tape at the far end of the cable may be loose. If so,

secure it with scotch tape or similar to prevent it from falling off
during cable routing.

Y Proximity Switch

Locate 8mm threaded hole to the left of the spindle/router

Содержание PRSalpha























































































Результаты поиска

Содержание PRSalpha

Отзывы:

Похожие инструкции для PRSalpha

Бренды по названию

Популярные бренды

ShopBot PRSalpha, Инструкция по сборке

Результаты поиска

Содержание PRSalpha

Отзывы:

Похожие инструкции для PRSalpha

Бренды по названию

Популярные бренды