ShopBot PRSalpha страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 100

background image

Section 2: Table Assembly • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 2-11

Mount Table Supports and Cross Supports to Rails

Use a zip tie to move the T-nuts (positioned earlier) so the
threads are in line with the mounting holes.

Attach the table support to the rail using two 5/16”
hex bolts, and flat washers on each side of the upper
supports.

NOTE:

Do not use lock washers with the table sup-

port assembly.

Do not fully tighten the table supports yet.

Install Cross Supports

Use an assistant or sling(s) to hold the cross supports in
place for installation.
Line up T-nuts that were installed earlier with the mount-
ing holes using a zip tie.

Attach each end of the cross support with 5/16” Hex bolt,
lock washer, and flat washer into the T-nuts.
Line up the leading edge of each cross support with mark
and snug the bolts enough to compress the lock washers.

Do not fully tighten the cross supports.

«
...
23
24
25
26
27
...
»

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Похожие инструкции для PRSalpha

Бренд: Watts Страницы: 2

Бренд: BADODOSECURITY Страницы: 8

Бренд: Ebyte Страницы: 38

Бренд: EBS Страницы: 30

Бренд: halstrup-walcher Страницы: 39

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: YASKAWA Страницы: 49

Бренд: M-system Страницы: 17

Бренд: µ-Dimension Страницы: 48

Бренд: µ-Dimension Страницы: 2

Бренд: WAGO Страницы: 16

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

Бренд: tell Страницы: 11

Бренд: BlitzRotary Страницы: 41

Бренд: M-system Страницы: 7

VEGACAP 60 Series

Бренд: Vega Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды