manualshive.com logo in svg

ShopBot PRSalpha, Инструкция по сборке

Поделиться
Скачать
ShopBot PRSalpha Скачать руководство пользователя страница 91

Section 11: Secure Table and Spoil Board • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.  

 page 11-1

Section 11. Secure Table and Spoil Board

Introduction

These instructions are based on a ShopBot PRSalpha 96-48. Larger or smaller table sizes will require 
additional baseboards and/or cutting material to fit.

Hardware

Part Name

Quantity

ShopBot Part Number

Notes

3/8 x1 1/2” carriage bolts

000953

ShopBot supplied

3/8” Lock washer

000092

ShopBot supplied

3/8” Flat washer

000444

ShopBot supplied

3/8-16 Hex nut

000452

ShopBot supplied

3/4” cabinet grade plywood
3/4” Medium-Density Fiberboard (MDF)
Wood glue

1 Gallon

NOTE: 

If table size is greater than 96x48”, it will be necessary to tile multiple sheets to cover the full 

working area.

Refer to the table drawing for specs and measurements specific to machine.

Base Layer

The base layer should be a sheet of 3/4” cabinet-grade plywood. This is the foundation of the work-
bed, and will likely last the life of the tool. When choosing plywood, keep in mind that a higher number 
of plies typically creates a more stable board that is less likely to warp.

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды