ShopBot PRSalpha Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 100

ShopBot PRSalpha Скачать руководство пользователя страница 100

Section 12: Setup and Fine Tuning • May 2, 2016

© Copyright 2016 ShopBot Tools, Inc.

page 12-8

Install Push Bars

The Push Bar IInstallation document was provided with tool documentation, and can also be accessed
through http://www.shopbottools.com/ShopBotDocs/files/PushBarInstallation.pdf

Install Dust Foot

The Dust Foot Installation document was provided with tool documentation, and can also be accessed
through http://www.shopbottools.com/ShopBotDocs/files/SBG%2000326%20PRS%20Dust%20
foot%20install%202014%2010%2029.pdf

Install End Caps

Pop end caps into place at ends of side rails.

The Gantry Tool Assembly is complete.

For usage information, see the ShopBot Quick Start Guide, which was provided with tool
delivery, and can be found at www.shopbottools.com/ShopBotDocs/gantry ShopBot Quick
Start Guide.

For maintenance and troubleshooting information, refer to http://www.shopbottools.com/
ShopBotDocs/maintenance.htm.

Resources

To the best of our knowledge, these links are current. If you find that any of them are no longer work-
ing, please contact us so that we can update them accordingly.

Detailed chip load charts:

http://www.onsrud.com/plusdocs/Doc/index.html?model.code=FeedSpeeds

ShopBot user’s forum:

http://www.talkShopBot.com/forum

Vectric training videos:

http://www.vectric.com/WebSite/Vectric/support/support_vcw_tutorials.htm
Additional Vectric support available within VCarve software: click on Help > Help Contents for an inter-
active PDF file.

100K Garages:

Post information, bid on projects, and connect with people who want to get things made!
http://www.100kgarages.com

«
...
98
99
100

Содержание PRSalpha





































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды