MX-C250 SIMULATION 6 – 5
46
1
Used to adjust the copy density in the color copy mode.
2
Used to adjust the copy density in the monochrome copy mode.
4
Used to adjust the density in the color image send mode.
5
Used to adjust the density in the monochrome image send mode.
9
Used to adjust the scan image density.
19
Used to set the operating conditions for the density scanning (exposure) of monochrome auto copy mode
documents.
21
Copy color balance adjustment (Manual adjustment)
23
Used to set the density correction of copy high density section (High density tone gap supported).
24
Color balance adjustment (Auto adjustment)
27
Used to adjust the gamma/density of copy images, texts, and line image edges.
32
Used to set the AE reactivity control.
37
Used to adjust the color document reproducibility in the monochrome copy mode.
39
Used to adjust the sharpness of FAX send images.
40
Used to adjust the FAX send image density. (Collective adjustment of all the modes)
41
Used to adjust the FAX send image density. (Normal)
42
Used to adjust the FAX send image density. (Fine)
43
Used to adjust the FAX send image density. (Super Fine)
51
Used to adjust the gamma for the copy mode heavy paper mode and the image process mode.
(Manual adjustment)
52
Used to reset the copy color balance adjustment (adjustment for each dither) to the default value.
(The set values of SIM46-51 and SIM46-54 are set to the default values.)
54
Used to reset the copy color balance adjustment (auto adjustment for each dither).
48
1
Used to adjust the scan image magnification ratio (in the main scanning direction and the sub scanning direc-
tion).
6
Used to adjust the rotation speed of each motor.
49
1
Used to perform the firmware update.
2
Used to perform the FPGA update.
50
1
Copy image position, image loss adjustment
5
Used to adjust the print lead edge image position. (PRINTER MODE)
6
Used to adjust the copy image position and the image loss. (RSPF mode)
RSPF
10
Used to adjust the black print image magnification ratio and the off-center position.
(The adjustment is made separately for each paper feed section.)
12
Used to perform the scan image off-center position adjustment.
(The adjustment is made separately for each scan mode.)
20
Image registration adjustment (Manual adjustment)
22
Used to adjust the image registration. (Main scan direction, sub scan direction)
(Auto adjustment)/OPC drum phase adjustment (Auto adjustment)
51
1
Used to adjust the ON/OFF timing of the secondary transport voltage.
2
Used to adjust the contact pressure (deflection amount) on paper by the main unit and the RSPF resist roller.
(This adjustment is performed when there is a considerable variation in the print image position on the paper
or when paper jams frequently occur.)
53
8
Used to adjust the document lead edge reference and the SPF mode document scan position.
9
Used to detect the dirt of the SPF
10
Used to set the display of the dirt detection position of the SPF
55
1
Used to set the specifications of the engine control operations. (SOFT SW)
2
Used to set the specifications of the scanner control operation. (SOFT SW)
3
Used to set the specifications of the controller operation. (SOFT SW)
56
2
Used to backup the data in the EEPROM and Flash memory (including user authentication data) to the USB
memory. (Corresponding to the device cloning and the storage backup.)
5
Used to print out the each data and simulation list
60
1
Used to check the operations (read/write) of the MFP PWB memory.
61
1
Used to check the LSU polygon motor rotation and laser detection.
LSU
3
Used to set the laser power
4
Used to print the print image skew adjustment pattern. (LSU unit)
63
1
Used to display the shading correction result.
Scanner
2
Used to perform shading.
3
Used to perform scanner (CIS) color balance and gamma auto adjustment.
Scanner
5
Used to perform the scanner (CIS) color balance and gamma default setting.
12
Used to set the target color balance of the copy mode auto color balance adjustment.
64
1
Test print. (Self print) (Color mode)
2
Test print. (Self print) (Monochrome mode)
4
Printer test print. (Self print)
5
Printer test print. (Self print) (PCL)
6
Printer test print. (Self print) (PS)
65
10
Used to set the display of key standby time.
Main
Sub
Functions
Section
