Sharp MX-C250, Руководство по обслуживанию

Страница: 127 / 294

MX-C250 SIMULATION 6 – 50
50-5
Purpose
Adjustment
Function (Purpose)
Used to adjust the print lead edge image
position. (PRINTER MODE)
Section
Operation/Procedure
1) Select a target adjustment item (DEN-C) with Arrow key.
2) Enter the adjustment value using the 10 keys.
3) Press [OK]/[START] key.
The set value is saved, and the adjustment check pattern is
printed.
4) Measure the distance from the paper lead edge the adjustment
pattern to the image lead edge, and check to confirm that it is in
the standard adjustment value range.
Standard reference value: 4.0 +/- 2.0mm
When the adjustment value is increased, the distance from the
paper lead edge to the image lead edge is increased. When the
adjustment value is decreased, the distanced is decreased.
When the set value is changed by 1, the distance is changed by
about 0.1mm.
When the adjustment value is increased, the distance from the paper lead edge to the image lead edge is increased. When the adjustment
value is decreased, the distance from the paper lead edge to the image lead edge is decreased.
When the set value is changed by 1, the distance is changed by about 0.1mm.
50-6
Purpose
Adjustment
Function (Purpose)
Used to adjust the copy image position and
the image loss. (RSPF mode)
Section
RSPF
Operation/Procedure
1) Select an item to be set with 10 keys.
2) Enter the set value with 10 keys.
3) Press [OK]/[START] key.
The set value in step 2) is saved.
Item 1, 2: When the adjustment value is increased, the scan timing
is delayed.
Item 3 - 8: When the adjustment value is increased, the image loss
is increased.
Item 1 - 8: 1 step = 0.1mm change
Item/Display Content
Setting
range
Default
value
NOTE
1 DEN-C
Used to adjust the print
lead edge image posi-
tion.
(PRINTER MODE)
1 - 99 50
Adjustment value too align the print lead edge for the printer. When the
adjustment value of this item is decreased by 1, the printer print start position
in the paper transport direction is shifted to the lead edge by 0.1mm.
2 DEN-B
Rear edge void area
adjustment
1 - 99 40
Void amount generated at the paper rear edge. When the adjustment value
of item B (DEN-B) is decreased by 1, the print area adjustment value in the
sub scanning direction for the paper transport direction is decreased by
0.1mm.
3 FRONT/REAR
FRONT/REAR void area
adjustment
1 - 99 35
Adjustment of the void amount generated on the left and right edges of paper.
When the adjustment value is increased, the void amount is increased.
4 DENB-MFT
Manual feed rear edge
void area adjustment
correction value
1 - 99 50
Fine adjustment value of each paper feed source for the adjustment value of
DEN-B
5 DENB-CS1
Tray 1 rear edge void
area adjustment correc-
tion value
1 - 99 50
6 DENB-CS2
Tray 2 rear edge void
area adjustment correc-
tion value
1 - 99 50
7 DENB-ADU
ADU rear edge void aria
adjustment correction
value
1 - 99 50
Item/Display Content
Setting
range
Default
value
1 SIDE1
Front surface
document scan
position adjust-
ment (CIS)
1 - 99 50
2 SIDE2
Back surface doc-
ument scan posi-
tion adjustment
(CIS)
1 - 99 50
3
Image
loss
amount
setting
SIDE1
LEAD_EDGE
(SIDE1)
Front surface
lead edge image
loss amount set-
ting
0 - 99 10
4
FRONT_REAR
(SIDE1)
Front surface side
image loss
amount setting
0 - 99 10
5
TRAIL_EDGE
(SIDE1)
Front surface rear
edge image loss
amount setting
0 - 99 35
6
Image
loss
amount
setting
SIDE2
LEAD_EDGE
(SIDE2)
Back surface lead
edge image loss
amount setting
0 - 99 10
7
FRONT_REAR
(SIDE2)
Back surface side
image loss
amount setting
0 - 99 10
8
TRAIL_EDGE
(SIDE2)
Back surface rear
edge image loss
amount setting
0 - 99 35
Item/Display Content
Setting
range
Default
value