Rockwell Automation PowerFlex 700S, Руководство пользователя, Страница: 89 / 318

Programming and Parameters 3-31
PowerFlex 700S Phase II AC Drive User Manual - Publication 20D-UM006G-EN-P – July 2008
190 PI Integ Output
Displays the output value of the integral channel of the Process Control regulator. A value of
1 can represent either base motor speed, motor rated torque, or 100% for some external
function.
Units:
Default:
Min/Max: P.U.
0.0000
-/+8.0000 pu RO Real
191 PI High Limit
The high limit of the Process Control regulator output. A value of 1 can represent either base
motor speed, motor rated torque, or 100% for some external function.
Units:
Default:
Min/Max: P.U.
0.1000
0.0000/8.0000
✓
RW Real
192 PI Lower Limit
The low limit of the Process Control regulator output. A value of 1 can represent either base
motor speed, motor rated torque, or 100% for some external function.
Units:
Default:
Min/Max: P.U.
-0.1000
-8.0000/0.0000
✓
RW Real
196 ParamAccessLevel
The value of this parameter establishes the level of parameter access for the Human Interface
Module (HIM).
•
Value 0 - Basic grants access to the minimum number of parameters
•
Value 1 - Advanced grants access to a larger group of parameters
Default:
Options: 0 =
0 =
1 = “Basic”
“Basic”
“Advanced” RW 16-bit
Integer
201 Language
Selects the display language when using an LCD HIM. Currently, only option 0 - “English” is
available.
Default:
Options: 0 =
0 =
1 = “English”
“English”
“Alt Language” RW 16-bit
Integer
202 Time Axis Rate
Sets rate (1/sec) for the Time Function Generator to ramp from an output of 0 to 1 and from 1
to 0.
Units:
Default:
Min/Max: /Sec
1.0000
0.0100/20.0000
✓
RW Real
203 Time Axis Output
The output of the Time Function Generator. When the Time Function Generator is enabled by
Par 151 [Logic Command] bit 3 “Time Axis En”, or Par 153 [Control Options], bit 24 “Time Axis
En”, the value of this parameter ramps from 0 to 1 at a rate determined by Par 202 [Time Axis
Rate]. Conversely, when the Time Function Generator is disabled, the value of this parameter
ramps from 1 to 0.
Default:
Min/Max: 0.0000
0.0000/1.0000 RO Real
204 LimGen Y axis Mx
Sets Par 207 [Limit Gen Hi Out] and Par 208 [Limit Gen Lo Out] when the absolute value of
Par 206 [LimGen X axis In] is greater than or equal to 1.
Units:
Default:
Min/Max: P.U.
0.2500
0.0000/8.0000
✓
RW Real
205 LimGen Y axis Mn
Sets Par 207 [Limit Gen Hi Out] and Par 208 [Limit Gen Lo Out] when the absolute value of
Par 206 [LimGen X axis In] is equal to 0.
Units:
Default:
Min/Max: P.U.
0.0500
0.0000/8.0000
✓
RW Real
206 LimGen X axis In
The X axis input to the Limit Generator. Typically this parameter is linked to a speed reference
or to
Par 203 [Time Axis Output].
Default:
Min/Max: 0.0000
-/+8.0000 pu
✓
RW Real
207 Limit Gen Hi Out
Displays the positive output of the Limit Generator. When Par 206 [Limit Gen X axis In] is
greater than or equal to 1, this value equals Par 204 [Limit Gen Y axis Mx]. When Par 206
[Limit Gen X axis In] is equal to 0, this value equals Par 205 [Limit Gen Y axis Mn]. For values
of X Axis input between 0 and 1, the value of this parameter is interpolated from Y axis min.
and max. values. Typically it is linked to
Par 188 [PI Integ HLim].
Units:
Default:
Min/Max: P.U.
8.0000
0.0000/8.0000 RO Real
208 Limit Gen Lo Out
Displays the negative output of the Limit Generator. The value of this parameter is the
negative of
Par 207 [Limit Gen Hi Out]. Typically it is linked to Par 189 [PI Integ LLim].
Units:
Default:
Min/Max: P.U.
-8.0000
-8.0000/0.0000 RO Real
210 PeakDtct Ctrl In
Sets the configuration of the two peak/level detectors. Peak detection (when “set” and “hold” are off) causes the output to capture the peak min./max.
•
Bit 2 “Peak1SelHigh” and bit 6 “Peak2SelHigh” determine if the peak/level detector is positive or negative. If the bit is set the detector detects positive peaks or
levels above the preset. If the bit is not set the detector detects "valleys" or levels below the preset. The output shows the min. or max. peak.
•
Bit 0 “Peak 1 Set” bit is used to reset the output to the value in Par 214 [PeakDtct1 Preset] (default 0). Bit 4 “Peak 2 Set” bit is used to reset the output to the
value in Par 218 [PeakDtct2 Preset] (default 0).
•
Bit 1“Peak 1 Hold” is used to hold the output at the present value in Par 214 [PeakDtct1 Preset]. Bit 5 “Peak 2 Hold” is used to hold the output at the present
value in Par 218 [PeakDtct2 Preset].
No.
Name
Description
Values
Linkab
le
R
ead-Wr
ite
Da
ta
T
ype
Options
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
Re
se
rv
ed
P
eak
2SelHigh
P
eak
2
Hold
P
eak
2
Set
Re
se
rv
ed
P
eak
1SelHigh
P
eak
1
Hold
P
eak
1
Set
Default 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
0 = False
1 = True