REXROTH Sytronix DRn 5020 Скачать руководство пользователя страница 58

Страница: 58 / 146

6.4.5

Connection of the Pressure Transducer

NOTICE

Malfunction of the DRn system due to use of a pressure transducer not suita‐

ble for the DRn system!
Damage to property!
●

Use only the pressure transducer set of the Bosch Rexroth HM20 series

included in the DRn system (see

chapter 1 "About this Documentation"

on page 7

, data sheet 30272).

●

Assemble the pressure transducer in suspended position (hydraulic con‐

nection at the top). In this position the pressure transducer is optimally

ventilated.

●

Do not install an additional valve (except for check valve) in the line be‐

tween the pump and the pressure transducer (apart from the pre-load

valve).

●

If there is no pre-load valve in the system, you can assemble the pres‐

sure transducer directly at the pump or at the directional valve (possibly

control block).

●

Connect a pressure transducer with a sufficient line diameter (no mini‐

miss connections!).

●

Connect the pressure transducer at terminals AI2 and GND to the figure

below.

Fig. 6-13:

Connection of the pressure transducer

●

USE external 24 V power supply (not from EFC 5610).

●

USE ONLY shielded cables.

●

GND must be well connected.

●

The cable shielding must be well connected to the grounding

terminal.

Bosch Rexroth AG

DOK-SYTROX-DRN5020****-IT05-EN-P

56/143

Frequency-Controlled Pump Drive System Sytronix DRn 5020

Assembly and Installation

Содержание Sytronix DRn 5020



















































































































































Результаты поиска

Содержание Sytronix DRn 5020

Отзывы:

Похожие инструкции для Sytronix DRn 5020

Бренды по названию

Популярные бренды

REXROTH Sytronix DRn 5020, Руководство по эксплуатации

Результаты поиска

Содержание Sytronix DRn 5020

Отзывы:

Похожие инструкции для Sytronix DRn 5020

Бренды по названию

Популярные бренды